Hydrocarbon removal filters remove oil gasoline diesel fuel solvents sheen and other hydrocarbons in a single pass. Absorbent media permanently bonds to hydrocarbons. Low pressure drop even when filters have been fully saturated. High flow rates. Applications:. Gas/Oil Facilities. Leisure/Commercial shipping bilge water. Storm water runoff (airports parking lots). Factory and Industrial processes. Car and Truck Washes. Oil spill remediation projects. Machine and Repair shops. Tank farms and Terminals. Plating baths. Manhole effluent. Length: 20 (50.8 cm). Outer Diameter: 4.5 (11.4 cm). Flow Rate: 20 gpm. Initial Pressure Drop: 1.5 psid. Temperature Rating: 140 °F.
$275.28
from
Watts Flowmatic WR100 Watts Water Filter Wrench
The Watts WR100 is a Sump Wrench for Residential/RV Housings. The Watts Flowmatic WR-100 wrench makes changing water filters easy. The Watts Flowmatic WR100 Wrench can be used to loosen the bottom of the housing during cartridge replacement. Slide circular end over housing until a snug fit is achieved and unscrew. The Watts Flomatic WR-100 Wrench is a filter housing wrench for removing housing body from housing cap and is used for the replacement of filter cartridges. Do NOT use the wrench to tighten the sump. The width is 4-1/4 and width inside notches is 3-13/16 .
$17.99
from
Watts Flowmatic WW-FF Wrench for Full-Flow Clear Housings
Use the Watts Flowmatic WW-FF water filter wrench for Watts 10 Full-Flow Housings and Watts 20 Full-Flow Housings. Use the Watts Flomatic wrench on the Watts W10FFPH1CBPR Clear Housing and the Watts W20FFPH1CBPR Clear Housing. Do not use the Watts WW-FF spanner wrench to tighten the housing sumps. Overtightening the sump can cause damage to the o-rings and make re-opening the housing sump difficult. You should only hand tighten the housing sump. The Watts WW-FF wrench makes replacing water filters easy.
$19.99
from
Watts Flowmatic PEX12-100 .5 in. CTS PEX Pipe for Plumbing Applications
This PEX tube is 1/2 CTS (Copper Tube Size) Inside Diameter. It is 5/8 Outside Diameter. The bend radius is 5 . PEX (or crosslinked polyethylene) is part of a water supply piping system that has several advantages over metal pipe (copper iron lead) or rigid plastic pipe (PVC CPVC ABS) systems. It is flexible resistant to scale and chlorine doesn t corrode or develop pinholes is faster to install than metal or rigid plastic and has fewer connections and fittings. PEX is cross-linked polyethylene. Through one of several processes links between polyethylene molecules are formed to create bridges (thus the term cross-linked). This resulting material is more durable under temperature extremes chemical attack and better resists creep deformation making PEX an excellent material for hot water and other applications. PEX is ideally suited for potable water plumbing applications. It is flexible making it easy to install and service. PEX is able to withstand the high and low temperatures found in plumbing and heating applications and is highly resistant to chemicals found in the plumbing environment. Flexible PEX systems are quieter than rigid piping. PEX systems have fewer joints and are easier to install providing a lower cost installation over traditional plumbing materials. PEX s strength at temperatures ranging from below freezing up to 180 degrees Fahrenheit makes it an ideal piping material for hot and cold water plumbing systems hydronic radiant heating systems snow melting applications and even ice rinks and refrigeration warehouses. WaterPEX Tubing is also known as Sea Tech PEX Tubing and Aquapex Tubing and is available in multiple colors for ease of water line identification. PEX is included in all of the major model plumbing codes used in the United States and Canada CSA IAPMO SBCCI BOCA ICBO IPC and NSPC and approved by HUD for hot and cold potable water plumbing use. PEX is designed for indoor and buried applications only. PEX Tubing should not be exposed to dir
Dimensions: 10 x 4.72 . Maximum Operating Pressure: 125 psi (8.75 bar). Maximum Temperature: 125°F (52°C). Minimum Temperature: 40°F (4°C). Material sumps and caps: FDA grade polypropylene. Material O-rings: EPDM. Cycles Test: Tested to 150 000 cycles from 0 to 125 psi. Burst test: Tested to 500 psi.
The Etzwretrokit Zero-Waste Retro Kit converts existing traditional 4 and 5 stage reverse osmosis systems to Zero Waste. The Etzwretrokit can convert your existing Reverse Osmosis unit into a Zero Waste System by adding a few additional components. The Etzwretrokit RO Zero Waste retro fit kit redirects the rinse water that normally would go down the drain and pushes it into the hot water side of your home plumbing system. The Reverse Osmosis Zero-Waste Kit ETZWRETROKIT puts the rinse water into the hot water side of your plumbing system giving you the ability to still use the water for everyday things such as washing dishes cleaning and other uses that you use hot water for. The converted reverse osmosis system produces high quality drinking water and you have the benefit of using the rinse water for uses that do not require the purity needed for drinking. The Etzwretrokit Zero-Waste RO Kit conserves water by returning unused water from your RO system back to your home s hot water supply. The Etzwretrokit Zero-Waste RO Kit helps to increase membrane production and provides for faster filling of your reverse osmosis storage tank. The Reverse Osmosis Etzwretrokit Zero Waste Retro Kit helps to eliminate noise created by the air-gap faucet. The Etzwretrokit Reverse Osmosis Kit will adapt to any traditional 4 stage or 5 stage reverse osmosis system. However it is NOT for use with models WP-5 WP-4V or Manifold Units.
$215.72
from
Watts Flowmatic FPP-0.2-975-DOE Watts Flow-Max High Purity
Watts FPP-0.2-975-DOE Flow-Max High Purity (10 x 2.5 ). Made from the finest materials. High quality components. Satisfaction ensure